Research progress of preparation methods of strontium titanate at present, the main preparation methods of strontium titanate are sol thermal method. Sol-sol-whether in metallic materials, or in organic and inorganic non-metallic materials, adding appropriate amount of strontium and its compounds can change some of its properties and even make it have special functions, so it has the name of metal monosodium glutamate. Strontium titanate (SrT iO 3) is one of the important strontium compounds. Strontium titanate has the advantages of superconductivity, semi-conductivity, gas sensitivity, heat sensitivity and photosensitivity, low boundary loss, high dispersion frequency, high dielectric constant and low electrical loss. Compared with calcium material, it has better temperature stability and high compressive strength. Therefore, it is a kind of electronic ceramic material widely used in the electronic industry. Replacing SiO 2 with it in memory can increase the storage capacity by more than 30 times. Gel method, chemical precipitation method, high temperature solid phase method, microwave method, plasma method and hydrogel method gel method is a method to prepare SrT iO 3 thin films. Generally, using titanium salt and strontium salt as raw materials and organic compound as chelate, homogeneous sol is prepared in organic solvent. Strontium titanate powder can be prepared by drying the gel and roasting it at low temperature (below 900) for several hours. Nano SrT iO 3 ceramic powders were synthesized from T iC 14.srcl 2.6h 2O by sol-gel process (ISG process for short). Studies have shown that due to the complexation of citric acid and other actions, the sol is stable and the gel is evenly distributed. In the transition process of SrO_T iO 2 composite oxide gel to crystalline phase, simple oxides without intermediate phase are generated. After treatment, the precursor SrO_T iO 2 can directly generate a single cubic [6]. In addition, the oxygen sensor made of oxygen sensor is widely used to control the thin combustion of automobile.
Related Posts
Industrial grade lithium carbonate, salt lake purification method
Lithium carbonate, an inorganic compound whose chemical formula is Li2CO3, is a colorless monoclinic crystal or white powder. The density of 2.11 g/cm3. Melting point 618 ℃ (1.013 * 10 ^ 5 pa). Dissolved in dilute acid. Slightly soluble in water, solubility in cold [...]
Application of lanthanum aluminate
Lanthanum aluminate belongs to ABO3 perovskite structure compounds, with a small dielectric constant, low dielectric loss, good lattice mismatch, thermal expansion coefficient, good chemical stability, wide energy gap, specific surface area is big, has a certain activity, good thermal stability, has been widely applied [...]
Preparation technology of nano bismuth oxide
For the preparation of nano bismuth oxide, the main methods include plasma method, melt spray oxidation method, chemical vapor condensation method, sol-gel method, chemical precipitation method, etc. Each method has its own characteristics. The plasma method has the advantage of short process, but requires [...]
Gadolinium zirconate material for thermal barrier coatings
Advanced aero-engine technology is one of the important symbols of a country’s scientific and technological level, industrial base and comprehensive national strength. In order to improve the performance of aeroengine, higher requirements should be put forward for turbine inlet gas temperature. Generally speaking, the [...]
Properties of nano-aluminum nitride filled ptfe composites
Nano aluminum nitride powder has high specific surface area, high hardness, high thermal conductivity, high insulation and other characteristics, belongs to diamond-like nitride, can be stable to 2200℃, high strength at room temperature, good compatibility with the matrix interface, can improve the thermal conductivity [...]
A modification method of nano-samarium oxide MC nylon
MC nylon is a new type of engineering plastic, which is made of caprolactam as the main raw material by anion polymerization under atmospheric pressure. MC nylon is gradually replacing copper, aluminum, steel and other metal materials and is widely used in textile, rubber, [...]
What are the characteristics and uses of nano-zirconium carbide?
Performance Characteristics 1. High purity, small particle size, uniform distribution, large specific surface area, high surface activity, low loose packing density. 2 with high temperature resistance, oxidation resistance, high strength, high hardness, good thermal conductivity, good toughness. 3. Zirconium carbide is an important high melting point, high [...]
Chemical properties and uses of stannous chloride
Stannous chloride, chemical formula SnCl2, also known as tin dichloride. The former is a transparent crystal with a melting point of 246℃, a boiling point of 652℃, and a relative density of 3.95. Soluble in water and oxidized in air to form insoluble chloride [...]
Research status of strontium titanate
Currently, various electronic instruments, home audio and video equipment and microcomputer, etc., in order to prevent the equipment from the external power supply cord, transmission of noise and signal lines or air surge voltage, as well as the human body electrostatic factors lead to [...]
Method for preparing subnickel oxide from nickel precipitate
The invention relates to a method for preparing subni oxide by reusing nickel precipitate. Firstly, the unqualified products produced by solution precipitation are screened to obtain a part of nickel precipitate with diameter > 5.0μm and a part of nickel precipitate with diameter ≤5.0μm. [...]